|
Welcome to CNC Router Community! :wave:
|
|
9
|
162
|
October 17, 2026
|
|
Do you really need 316L, or is 304 fine for your machined parts?
|
|
6
|
0
|
November 4, 2026
|
|
RC1325 vacuum zones only hold full sheets — small nested parts lift no matter what I try
|
|
1
|
0
|
November 4, 2026
|
|
Spindle whining at 18k on a 4x8 router: what we check before pulling the spindle
|
|
6
|
164
|
November 4, 2026
|
|
1/2" aluminum on a 4x8 router: our setup and what actually limits it
|
|
6
|
148
|
November 4, 2026
|
|
ER32 collets: how much runout before you retire them?
|
|
1
|
0
|
November 4, 2026
|
|
Chip welding on 6061 with a 2-flute cutter: what we recommend on a 3 kW router
|
|
10
|
191
|
November 4, 2026
|
|
Compression bit spiking load in 18mm ply, tooling or tuning?
|
|
9
|
120
|
November 4, 2026
|
|
Design engineer here — is learning CNC programming actually the fastest way to pick up manufacturing knowledge?
|
|
0
|
0
|
November 4, 2026
|
|
ESR vs conventional 1.2344 / H13 — does the cleaner steel actually show up in the polish?
|
|
0
|
0
|
November 4, 2026
|
|
Sanity check on a small-batch shop plan around a benchtop machine
|
|
5
|
60
|
November 3, 2026
|
|
Y driver swap only or full closed loop swap on 4x8 router
|
|
6
|
117
|
November 3, 2026
|
|
When does a 1.2714 hammer die block beat H13 — and how do you harden the big ones?
|
|
4
|
0
|
November 3, 2026
|
|
VFD tripping OC on spindle ramp-up: the order we work through
|
|
9
|
176
|
November 3, 2026
|
|
How much CFM does an RC1325 actually need for nested sheet work?
|
|
5
|
0
|
November 3, 2026
|
|
How did you actually fix the 0.002" runout on that MDF fixture?
|
|
11
|
161
|
November 3, 2026
|
|
Getting into knife making — Langmuir MR-1 or Carvera as a first machine on a $10k budget?
|
|
0
|
0
|
November 3, 2026
|
|
1.2311 or 1.2312 for a 600 x 400 cavity block — how much polishing trouble does the sulfur really cause?
|
|
0
|
0
|
November 3, 2026
|
|
[Announcement] Forum Coin (ROCTECH) Now Live: Tipping, Balance & Monthly Airdrops
|
|
8
|
118
|
November 2, 2026
|
|
Galaxy Midas 10 lathe lost its parameters after the battery died
|
|
3
|
0
|
November 2, 2026
|
|
Full-sheet plywood router build - does my belt drive math hold up?
|
|
5
|
0
|
November 2, 2026
|
|
3-flute or 4-flute carbide for roughing deep 6061 pockets on a VF2?
|
|
0
|
0
|
November 2, 2026
|
|
How much of our heat treat scatter is actually the steel? (scrap residuals)
|
|
0
|
0
|
November 2, 2026
|
|
Posting arcs on a 1325: IJK or R, and does the retract difference matter?
|
|
1
|
0
|
November 1, 2026
|
|
Haas VF-2 0.125" thin 6061-T6 bracket edge burring, tested 3 feeds, need DOC/WOC advice
|
|
7
|
171
|
November 1, 2026
|
|
DMC 60 T / iTNC 530: can the pallet change run without confirmations?
|
|
6
|
15
|
November 1, 2026
|
|
Edge finder touch-off: 0.01 or 0.001 steps?
|
|
6
|
22
|
November 1, 2026
|
|
How do you keep feed override and stickout tweaks from dying with the shift?
|
|
4
|
0
|
November 1, 2026
|
|
Spindle hit 190f mid-job, what else should i check?
|
|
10
|
200
|
November 1, 2026
|
|
Cutting detailed organic shapes in Baltic birch without top veneer chip-out
|
|
1
|
0
|
November 1, 2026
|